OneCalculatorHub
HomeRooms › Standard door size

Measurement of a Standard Door

ChartStandard dimensions — nothing to enter.

By Srinivas Gaddam, integration architect · Reviewed by OneCalculatorHub editors, figures checked against the cited standards · Updated 29 August 2026

A standard interior door is 80 inches tall (6 ft 8 in) and 28, 30 or 32 inches wide; the standard front door is 36 × 80 inches. Everything below is the door slab; the rough opening in the wall is 2 inches wider and 2½ inches taller.

Standard door sizes

DoorWidthHeightThicknessRough opening (W × H)
Interior — bedroom, bathroom28, 30 or 32 in (71, 76, 81 cm)80 in (203 cm)1⅜ in30–34 × 82½ in
Interior — closet, utility24 in (61 cm)80 in1⅜ in26 × 82½ in
Interior — accessible36 in (91 cm)80 in1⅜ in38 × 82½ in
Exterior — front door36 in (91 cm)80 in1¾ in38 × 82½ in
Exterior — tall front door36 in96 in (244 cm)1¾ in38 × 98½ in
Exterior — double entry72 in (two 36 in)80 in1¾ in74 × 82½ in
Sliding patio door72 in (183 cm)80 in74 × 82½ in
Bifold closet (pair)24, 30, 36 in80 in1⅛ inopening + ½ in
Garage — single96 or 108 in (8 or 9 ft)84 in (7 ft)same as door
Garage — double192 in (16 ft)84 in (7 ft)same as door

Older homes (pre-1970) often have 78 in doors and odd widths; measure the slab before ordering.

How this was worked out

Door sizes are quoted as width × height of the slab, in inches, and written as feet-inches in the trade: a 2/8 door is 2 ft 8 in (32 in) wide; a 6/8 door is 80 in tall. The slab is what you buy; the frame around it is the jamb, and the hole in the wall is the rough opening.

The rough opening is the slab width plus 2 inches (for the jamb and shims) and the slab height plus 2½ inches, measured from the subfloor. Pre-hung doors come with the jamb; you size the rough opening to them.

Measuring an existing door: width across the slab at the middle, height from top to bottom edge, thickness at the edge. Then the jamb depth — the wall thickness the frame sits in, 4⅝ in for a 2×4 wall with drywall, 6⅝ in for a 2×6 wall.

Sources. There is no published standard that fixes US residential door sizes — the sizes here are manufacturer conventions, highly consistent across the major producers and home centers, and they are stated as such rather than as a specification. Rough-opening allowances are the figures given in manufacturer installation guides and are trade allowances; each one is shown above so you can substitute the number in your own door's instructions. The accessible-width figure is the exception and is a legal requirement: the 32 in clear opening is set by the ADA Standards for Accessible Design, section 404. Last reviewed 29 August 2026.

Common questions

What is the standard size of an interior door?

80 inches tall and 30 or 32 inches wide for a bedroom; 28 inches for a small bathroom; 24 inches for a closet. Thickness is 1⅜ inches.

What is the standard front door size?

36 inches wide by 80 inches tall, 1¾ inches thick. Tall entries use 96-inch doors.

What is the rough opening for a 32 inch door?

34 inches wide by 82½ inches tall, for a pre-hung door with a standard jamb.

How thick is a standard door?

Interior doors are 1⅜ inches; exterior doors are 1¾ inches.

Next

Calculator + chartHow to measure a room for furnitureWill it fit, will it get through the door, and how much walkway is leftCalculator + chartHow to read a tape measureEvery mark on the tape, and a reader that turns any mark into a fraction, decimal and millimetresCalculator + chartSquare footage calculatorAny room, any unit, including L-shapesCalculator + chartHow to measure for blindsInside or outside mount — enter your six measurements and get the size to order